Charnwood C4 Operations Instructions download pdf (Page 4)

These appliances have been approved by HETAS as intermittent

operating appliances for burning dry seasoned wood logs only.

HETAS approval does not cover the use of other fuels either alone or

mixed with wood logs nor does it cover the instructions for use of

other fuels.

Tool required for fitting the riddling grate:

10mm Spanner

Pozidriv screwdriver

Before fitting the riddling grate (Fig. 1) remove the fuel retainer and

the wood ash retainer. The wood ash retainer is not required when

the riddling grate is fitted.

Undo the nut on the riddling blanking hole using a 10mm spanner.

Remove the cover and spacing washer (ensure you keep these in a

safe place as you will need to replace them if the riddling grate is

removed).

Feed the riddler rod through the hole on the right hand side of the

stove, and slide one washer onto the rod (if there is not sufficient

room to the right of the stove to do this then remove the riddler

knob, fit one washer over the rod and then slide the rod through the

hole from the inside of the stove).

Feed the rod through the two side fireplates and slide the other

washer on to the rod so that the washers end up outside the two side

fireplates. With the side fireplates pushed together fit the retaining

clips so that the washers come inside the clips.

Slide the side fireplates apart so that they rest against the sides of the

firebox. Slot in the front and rear support plates.

Fit the grate plates into position through the front and rear grate

support plates, making sure they locate correctly onto the riddler

rod. Fit the fuel retainer. Slide the ashpan under the grate.

FITTING THE RIDDLING GRATE

Congratulations on becoming the owner of a HETAS approved

Charnwood C-Series Stove. Your stove has been approved by DEFRA

to burn wood logs in a smoke control area if it is used in accordance

with these instructions. It is therefore very important that you read

and understand these instructions before using the stove.

FUEL

Before lighting the stove check with the installer that the work and

checks described in the Installation Instructions have been carried out

correctly and that the chimney has been swept, is sound and free

from any obstructions. The stove is not suitable for use in a shared

flue system.

Remember that the stove will be hot and that it is made from hard

materials – ensure that you have good balance before operating the

fire.

Do not use an aerosol spray on or near the stove when it is alight.

There is a risk of explosion or flash ignition of the spray.

The stove is suitable for intermittent operation.

This stove has been designated to burn wood. Only dry well seasoned

wood should be burnt on this appliance as burning wet unseasoned

wood will give rise to heavy tar deposits in the stove, on the glass and

within the chimney. For the same reason hard woods (such as Ash,

Beech and Oak) are better than soft woods (such as Pine and

Spruce). Burning wet unseasoned wood will also result in

considerably reduced outputs. The wood should be cut and split and

then left to season in a well ventilated dry place for at least one year

but preferably two years before use. Approximate suitable log sizes

are:

C4 & C6 255mm (10in) long and 75mm (3in) diameter

C5 & C8 305mm(12in) long and 75mm (3in) diameter

C7 380mm(15in) long and 75mm (3in) diameter.

PETROLEUM COKE IS NOT SUITABLE FOR USE ON

THIS APPLIANCE. ITS USE WILL INVALIDATE THE

GUARANTEE.

This stove is not designed to burn household waste.

For advice on other fuels please contact Charnwood.

When using the stove in situations where children, aged and/or

infirm persons are present a fireguard must be used to prevent

accidental contact with the stove. The fireguard should be

manufactured in accordance with BS 8423:2002.

OPERATING INSTRUCTIONS

Fig.1. Optional Grate Kit

Front Grate

Support

RH Side Grate

Support

Grate Plates

Rear Grate

Support

Riddler

Rod

Ashpan

LH Side Grate

Support

1 2 3 4 5 6 7 8 9 ... 23 24

Comments to this Manuals

No comments

Charnwood C4 Operations Instructions Page 4

Comments to this Manuals